Self-service Car wash Controller TMS-4.0 (English)

Self-service Car wash Controller TMS-4.0 (English)
Другие фото Self-service Car wash Controller TMS-4.0 (English)
  • Цена сейчас: 12 000,0 рублей
Варианты доставки

Описание Self-service Car wash Controller TMS-4.0 (English)

    The controller is  designed to automate self-service car washes. The device is a countdown time relay with different countdown times, depending on the selected start button. 
     The logic of the automation: the client puts money into the machine (coin acceptor or bill acceptor) and sees the deposited amount on the indicator. Immediately after depositing funds, the main light in the room is turned on. If there is a discount card, the client uses it and sees on the indicator the amount increased by the amount of the discount. Then the client can press any selected button, and depending on the included button, the amount will be spent at a different rate.   
     There are 6 buttons for starting the washing equipment and one button for a pause.
The counting intervals for the consumption of one ruble (counting coefficient) are from 0.1 to 25 seconds, the setting step is 0.1 seconds. The device has six working relays to control six different loads. Each button can simultaneously activate up to 5 any relays, arbitrarily selected by the user. The selection of relays to enable and the count rate for each button is configured in the settings menu. The settings are controlled by four buttons: "->", "+", "-" and "enter". All settings are displayed on the LCD indicator located next to the buttons on the main board. In the same menu, all other parameters of the device operation are configured, and also the total amount of accumulated funds for the entire operation time of the device is displayed. The entry to the settings menu is protected by two passwords.
     When you press the "Start 1" button, the combination of the relay corresponding to button 1 is turned on and the amount entered is consumed with the coefficient set to button 1. The indicator of button 1 lights up.
    When you press the "Start 2" button, or any other button for starting the equipment, the relay combination corresponding to button 1 will turn off and the relay combination corresponding to the pressed button will turn on (of course, the same relays can be turned on, with different combinations ). The spent amount will continue with the coefficient corresponding to the pressed button and the indicator of the corresponding button will light up.  
    When the "Pause" button is pressed, all operating relays are disconnected. The spending of the amount will be suspended for the duration of the free pause, after which the spending of the amount will continue with the coefficient corresponding to the "Pause" button. Immediately after depositing funds, the device is in the “Pause” position and a free pause is counting down, which is indicated by a blinking decimal point in the lowest digit of the indicator.
   When the entire deposited amount is spent, all operating relays are turned off. The main light in the room is on for another three minutes, then goes out.
    The client can press any button at any time and in any sequence, as well as additionally deposit funds during work.
     The device can work with any coin acceptor or bill acceptor operating in a pulse mode. The impulse price for entry 1 is always equal to one ruble. The impulse price for input 2 can be adjusted from 1 to 255 rubles. Configurable in the settings menu. Input 2 can work with token receivers, the impulse price of which can be equal to any amount. The parameters of the input pulses are strictly set to increase the noise immunity of the device, but can be changed by the manufacturer to match the bill / coin acceptors used. Therefore, this parameter should be discussed in advance with the supplier. Also, the input 1 pulse price can be made configurable and some other device parameters can be changed at will.
                                     Additional functions
      The device has a built-in thermostat with an external temperature sensor. The thermostat can work for heating or cooling. The response temperature and mode are set in the settings menu. The load is controlled by a relay similar to an operating relay.
    The device has an input for connecting a free access key for personnel with limited functions. Using a free access key is possible only when there is no money in the account, that is, when the device is not used by the client. When the key is triggered, the main light in the room immediately turns on (it also turns off immediately, without delay) and only two buttons become available - "Start 1" and "Pause".
   The device has an input for connecting a discount card reader. The discount card can be used after depositing funds into the account and only once. The discount does not apply to additional funds deposited during work. You can use a discount card again only after the account has been canceled. The discount for this device is 10%. After the discount card is triggered, the screen immediately displays the amount with the added interest, and the client sees that the amount deposited has increased. Only the deposited amount is added to the accumulated amount, excluding interest. For example: they deposited 150 rubles - the screen displayed "150", used the card - on the screen "165", and 150 rubles were added to the total amount in the device's memory. The amount with interest is spent in the same way as usual, with the same coefficients. 
        To save energy, the device can control the lighting in the room. Outside of work, only the emergency light is on. When you deposit funds, the main light comes on, and remains on as long as there is funds in the account. After the bill is used up, the light remains on for another three minutes so that the client can leave the room and goes out. The light is controlled using a relay similar to an operating relay.
    If the device is powered off during operation, the device memory stores the amount currently on the account. After the power is restored, this amount is shown on the display. "Memorization" occurs when the supply voltage drops below 7.5 volts. In this case, all relays are forcibly turned off, except for the light-on relay, button illumination and display. Only the point in the least significant digit is lit on the display. If after that the supply voltage disappears completely, then after the power is restored, more than 8.5 volts, the work will continue from the "Pause" state. If there was only a short-term "failure" of the power supply, then the work will continue in the same mode as before. Such short-term "dips" in power supply can occur when depositing funds when the coin / bill acceptors are drawing significant current. The device, as already mentioned, disconnects all loads to save energy, but it itself can function for some time and take into account the receipt of funds.
      The supply voltage of the device is 12-15 volts. The outputs of the operating relays and the lighting and heating control relays are supplied with a supply voltage, and it must enter the control cabinet to power the power contactors. When choosing a power supply, you must take into account the current consumption of these contactors. The device's own current consumption is not more than 1 Ampere. 
 Settings menu: The device is programmed with four buttons: "->", "+", "-" and "enter". All settings are displayed on the LCD indicator located next to the buttons on the main board. The "+" and "-" buttons change the settings - increase or decrease the parameter, or turn on or off the selected relay. Enter button - to go to the next configuration stage. Button "->" - to move from point to point within a stage (for example, to select the relay to be switched on). 
      It is possible to enter the programming mode only when the account is zero, since if there are funds on the account, the device performs the main work. The entrance to the mode is protected by the first password so that random people cannot change its settings. To enter the programming mode, press and hold the "enter" button for 3 seconds. After releasing the button on the LCD, the first line will display the word "PASSWORD", the second line will display four digits zero, and an arrow ">" pointing to the first zero. You must enter the first password. The "+" and "-" buttons set the desired digit in the most significant digit. Press the "->" button to move to the next digit. After entering all four digits of the password, press the "->" button again. If the password is entered incorrectly, the device will return to its original state, that is, four zeros will be displayed. If the password is entered correctly, the first line will display the word "OPEN". Now you need to press the "enter" button to go to the settings of the parameters of the buttons. 
The first line will display the word "BUTTON-", and then the number 1. Using the buttons "+" and "-" you can select any of the six buttons that you are going to customize. After selecting the desired button, press the "->" button. The first line will display "K =" and then the coefficient set for the selected button in the format XX, X s, that is, with an accuracy of tenths of a second. You can change the coefficient using the "+" and "-" buttons. For clarification, the coefficient is the time interval after which one ruble will be subtracted from the deposited amount. That is, the larger the coefficient, the slower the amount decreases. After setting the desired ratio, press the "->" button again to set the relay to be switched on. The second line displays six digits zero and an arrow “>” pointing to the first digit zero. In this case, the figure zero means that the corresponding relay is off, and one means that it is on. The relay can be switched on or off with the "+" and "-" buttons. Press the "->" button to go to the next relay. Up to five of the six available operating relays can be switched on simultaneously with one button. After configuring the enabled relays, press the enter button and the unit will return to the button select state so that other buttons can be configured in the same way. If the setting of the parameters of the buttons is finished, then press the "enter" button again, to go to the next stage - setting the parameters of the pause.
 The screen will display the word "Pause" and then "K =" and the actual coefficient for the paid pause mode. This coefficient is also adjusted using the "+" and "-" buttons and can be in the range from 0.1 to 25.5 sec. After setting the coefficient of the paid pause, press the "->" button to set the time of the free pause. The second line of the screen will display the inscription: "TIME =" and the actual time of the free pause. The time can be changed with the "+" and "-" buttons and it can be in the range from 0.1 min to 25.5 min.
   After pressing the “enter” button one more time, we proceed to setting the impulse price of input 2. The first line will display the inscription: “INPUT 2 =” and the actual impulse price for input 2. You can change the impulse price using the “+” and “-” buttons and it can range from 1 ruble to 255 rubles per impulse.
    After pressing the "enter" button again, proceed to setting the temperature of the thermostat triggering. The screen in the first line will display the word "temperature" and then the temperature of the thermostat, which can be changed with the buttons "+" and "-". The temperature can vary from -40 * to + 40 *. Further, after pressing the "enter" button, proceed to setting the operating mode of the thermostat. On the screen, the second line will display either the word "HEATING" - heating, or "COOLING" - cooling. You can change the mode using the "+" and "-" buttons. Attention! When the negative temperature of the thermostat is set and the cooling mode is selected, the corresponding relay will not turn on. The cooling mode works only at the set positive temperature.
   After another click on the "enter" button, we proceed to view the amount accumulated for the entire period of work. This mode is protected by another password. The password is entered in the same way as for the first password. After correct entry and pressing the "enter" button, the accumulated amount will be displayed on the first line of the screen. To reset the accumulated amount, simultaneously press and hold both buttons "+" and "-" for at least 5 seconds. After pressing the "enter" button again, exit the settings menu.

 

С этим товаром смотрят

Оставить отзыв о «Self-service Car wash Controller TMS-4.0 (English)»

Ваши знания будут оценены пользователями сайта, если Вы авторизуетесь перед написанием отзыва.
:*
:*
:
:
:
:*
:
Нет товаров для сравнения

Аэрозоль охладитель -50 градусов.

16.09.2013

Мы принимаем:

Яндекс.Метрика